Power Factor Measurement Using Pic Microcontroller Tutorial Pdf

Power factor measurement using pic microcontroller tutorial pdf

In our day-to-day life, we consume electrical energy for various purposes such as for powering electrical appliances, gadgets, devices, machines, and so on. So, it is essential to measure the amount of power consumed to generate electricity bill which is usually done by energy meters.

What is Power Measurement

In general, AC power is measured using various techniques, here in this article let us discuss about AC power measurement meter using PIC microcontroller.

The electrical power can be AC power or DC power, energy meter is used for measuring power. There are various types of energy meters, which are classified as digital energy meter, electronic energy meter, watt meter , three phase energy meter, single phase energy meter, AC power measurement meter, and so on. This can be represented as shown in the equation below.

Now, AC power measurement can be defined as the measurement of voltage, measurement of current, and measurement of power factor.

Categories

The microcontrollers generally operated and manufactured to work with voltage ratings less than or equal to 5V. So, it is not possible to directly measure AC voltage greater than V by giving high input voltages to microcontrollers which may cause temporary or permanent damage to microcontrollers. Hence, it is required to step down the high AC voltage around V to 5V for measuring voltage using microcontrollers.

Power Factor Improvement ( PFI ) Project Using Micro-Controller with Simulation Proteus 7 part-1

The AC voltage measurement using PIC microcontroller can be done using a difference amplifier or potential transformer. The difference amplifier or potential transformer is used to step-down the voltage and then by using analog to digital converter or rectifier the voltage reading is displayed on LCD display.

Power factor measurement using pic microcontroller tutorial pdf

The PIC microcontroller can be used for measuring AC current with the help of difference amplifier, shunt resistor, and analog to digital converter. Shunt resistors are used as transducers for converting current into voltage as microcontroller directly can not read current.

Thus, power factor can be defined as the cosine of the angle between current and voltage and is given as.

Hrabia monte christo ebook pdf chomikuj

To measure power factor using PIC microcontroller, the time difference between the voltage and current is determined using zero crossing detection with the help of a microcontroller external interrupt pin. Similarly, whenever current waveform interrupt is generated, then the timer stops counting and thus time difference is calculated.

This process repeated for a number of times say 20 to 30 and the average value is taken for better results.

Ativ book 8 m sata ssd

Hence, the time difference is used to determine the phase angle difference between voltage and current. Thus, power factor can be calculated using PIC microcontroller.

Power factor measurement using pic microcontroller tutorial pdf

Now, by substituting the values of voltage, current, power factor in the above power equation we can measure AC power. The meter used for measuring power factor can be called as power factor meter. The main aim of this project is solar energy measurement using multiple sensor data acquisition.

power factor meter using Arduino : How to measure power factor

The project utilizes a solar panel that changes its direction according to sunlight. The solar panel parameters such as intensity of light, temperature, voltage, and current are monitored and also sent to PC using RF.

Power factor measurement using pic microcontroller tutorial pdf

The project block diagram shown in the above figure consists of various blocks, including solar panel, temperature sensor, light sensor, voltage sensor and current sensor interfaced with the PIC microcontroller.

The sensors are used for measuring temperature, light, voltage, and current and is sent to the PC using RF, the same data is displayed over the LCD display.

Power factor measurement using pic microcontroller tutorial pdf

The power supply block, RF transceiver, PC, max, timer , and buzzer blocks are connected as shown in the above block diagram. The solar energy measurement can be achieved by measuring the factors such as temperature and light intensity that affect energy generation.

There are various types of meters that include power factor meter, digital energy meter, electronic energy meter, three phase power measurement, energy meter reading over internet, prepaid energy meter with GSM interface, programmable energy meter for electrical load survey.

Top Posts & Pages

Are you interested in designing electronics projects using the PIC microcontroller? Then, post your queries or ideas in the comments section below for technical help regarding project solutions. I need a program to measure power factor using pic micro. I try difrent program from net but not success in proteus simulator and microC.

Power factor measurement using pic microcontroller tutorial pdf

The circuit diagram, code, component list, documentation and other information could be shared with you when you purchase the project. Share This Post: Facebook.

Post navigation

What is Resistance : Definition, Formula and Laws. What is Resistivity : Definition and Its Formula. Leave this field empty.